HOME / PRODUCTS / TECHNICAL DATA

TECHNICAL DATA · EN / DIN

European sizes,
published in full.

Every welded-end ball valve we make is built to a metric DN series with ends prepared to European pipe outside diameters, so it drops into an EN pipe run without adaptors. Below is the complete dimension set — full bore and reduced bore — for the standard PN16 / PN25 / PN40 configurations.

DN15 – DN600

PN16 – PN40

WELDED ENDS · EN 10220 S1 / S2

FULL BORE & REDUCED BORE

STANDARDS REFERENCED

What the numbers are held to

Not for steam service. Imperial and ASME versions quoted on request.

BODY DESIGN EN 12516-1 ASME B16.34

END-TO-END EN 12982 series ASME B16.10

WELD END PREP EN 12627 ASME B16.25 / B16.11

PIPE OUTSIDE Ø EN 10220 S1 and S2 both machined on request

PRESSURE TEST EN 12266-1 shell and seat, every valve

FLANGED OPTION EN 1092-1 PN10 – PN40

TABLE 01

Full bore — DN15 to DN500

Bore equals nominal size, so the valve passes a pig and gives the lowest pressure drop in the line.

DN	PN	BORE	L	d1 S1	d2 S2	BODY Ø	H	H1	WEIGHT
DN15	40	15	230	21.3	18	42.4	120	48	1.1
DN20	40	20	230	26.9	25	48.3	130	48	1.2
DN25	40	25	260	33.7	32	60.3	140	55	2.5
DN32	40	32	260	42.4	38	76.1	150	57	3
DN40	40	40	280	48.3	45	88.9	160	57	4
DN50	40	50	300	60.3	57	109.0	175	58	5.5
DN65	25	65	300	76.1	76	133.0	224	72	12
DN80	25	80	320	88.9	89	159.0	244	79	15
DN100	25	100	320	114.3	108	180.0	289	79	29
DN125	25	125	350	139.7	133	219.1	365	109	30
DN150	25	150	400	168.3	159	273.0	422	112	55
DN200	25	200	400	219.1	219	351.0	520	129	94
DN250	25	250	580	273.0	273	425.0	555	136	180
DN300	25	300	680	323.9	325	508.0	637	179	245
DN350	25	350	760	355.6	377	580.0	680	197	430
DN400	25	400	914	406.4	426	670.0	750	229	670
DN500	25	500	1080	508.0	530	800.0	820	245	1100

All dimensions in millimetres · weights in kilograms · DN15 – DN50 supplied PN40, DN65 – DN500 supplied PN25FIG. 1

FIG. 1

One valve, two pipe outside diameters

European pipe comes in two wall-thickness families. The d1 column is the EN 10220 series 1 outside diameter and d2 is series 2 — our weld ends are machined to either, so the same valve fits both a standard and a heavy-wall line. Tell us which series your pipe is and we machine to it.

TABLE 02

Reduced bore — DN125 to DN600

Smaller bore, same body — lower cost and lighter handling where a pig or full flow area is not required.

DN	BORE	BODY Ø	d1 S1	d2 S2	WALL	L	H1	H2	STEM □	ISO 5211	WEIGHT
DN125	100	180	139.7	133	8	320	42	221	40	F07	22
DN150	125	219	168.3	159	8	350	83	245	50	F10	30
DN200	150	273	219.1	219	10	400	84	289	60	F12	50
DN250	200	351	273.0	273	10	530	90	306	84	F14	86
DN300	250	425	323.9	325	12	580	87	336	105	F16	145
DN350	300	508	355.6	377	14	680	102	395	110	F25	220
DN400	350	580	406.4	426	20	760	95	445	120	F25	400
DN500	400	670	508.0	530	22	914	95	522	150	F30	650
DN600	500	800	610.0	630	24	1080	105	610	170	F30	980

All dimensions in millimetres · PN25 standard series · ISO 5211 pad standard on every sizeFIG. 2

FIG. 2

End-to-end length follows the bore, not the DN

A reduced-bore DN300 and a full-bore DN250 share the same 580 mm face-to-face length, because both pass a 250 mm bore. That is how the EN welded-end series is laid out — so a change of series inside the same pipe run does not move your supports.

TABLE 03

Small sizes — DN10 to DN50, PN40

Branch lines, manifolds and instrumentation take-offs. Lever operated as standard.

DN	BORE	BODY Ø	d1 S1	d2 S2	WALL	L	H1	H2	WEIGHT
DN10	10	33	17.2	14	3	210	50	116	0.8
DN15	10	33	21.3	18	3	210	50	116	0.9
DN20	15	42	26.9	25	3	230	47	115	1.1
DN25	20	48	33.7	32	3	230	47	120	1.2
DN32	25	60	42.4	38	4	260	48	124	2.5
DN40	32	76	48.3	45	4	260	41	129	3
DN50	40	89	60.3	57	5	300	41	135	4

Standard series · larger PN40 sizes and PN25 DN50 – DN200 are quoted on requestFIG. 3

WORKED EXAMPLE

BALL VALVE – DN250 – PN25 – WE – 3

A fully welded gear-operated ball valve, DN250, PN25, welded ends. Issued with a dimensional drawing for approval before the body is welded.

ORDERING

How to read our model code

Quote the code and we build exactly that.

BALL VALVE Product type. Welded-body ball valve. The balancing version is written BALANCING VALVE and shares the same DN and pressure series.

DN250 Nominal size. DN15 to DN600 in this series — see the tables above for bore, length and weight.

PN25 Pressure rating. PN16, PN25 or PN40 as standard.

WE End connection. WE = welded ends, butt or socket. RF = raised face flanged to EN 1092-1.

3 Operator. 3 = gear, 6 = pneumatic, 7 = hydraulic, 8 = gas-over-oil, 9 = electric. Lever operated is the default and carries no digit.

BODY MATERIALS — Forged carbon steel ASTM A105 / A350 LF2 (P235GH) or stainless F304 / F316 / F316L (EN 1.4301 / 1.4404). Trim quoted separately.

TOLERANCES — Values shown are for the standard configuration and may be refined at drawing approval. Non-standard lengths, stem extensions and 3PE coating are available on request.

NOT COVERED HERE — Buried / extended-stem valves, balancing valves and flanged versions have their own tables. Ask for the relevant datasheet or send your line data and we will size it.